This came up on a batch of 9200 blades received, they show up as 4gb only and reports the 8gb is not licensed.
Below is the excerpt of the ticket (70067778) to fix it.
----------------------------------------------------------
Hi Robert,
I am happy to report we finally have a solution for you. The good news is, you will only need to access the switches and use the "feature add" command. Feature add requires admin; use the admin start command for this.
Please use the following license keys to modify your modules. You will need to run the command on the appropriate switch. Match the serial number included below, with the serial number reported by your IO Module:
Switch Type: SB9000 - 8G Key for the FC8G16 blade Serial Number: 1139E00017
Key: 40000000-LCAXBK/UXEFAY-1139E00017
Switch Type: SB9000 - 8G Key for the FC8G16 blade Serial Number: 1139E00025
Key: 40000000-LC88EJXABUMCY-1139E00025
Switch Type: SB9000 - 8G Key for the FC8G16 blade Serial Number: 1139E00010
Key: 40000000-LCFPCAGH2CBJ2-1139E00010
Switch Type: SB9000 - 8G Key for the FC8G16 blade Serial Number: 1139E00020
Key: 40000000-LCNUHW3CJGQ/2-1139E00020
Thanks for your patience through all of this. We are very sorry for the inconvenience.
Chris
P.S. Here is a breakdown of your Serial Numbers by chassis:
SW1 Chassis: 1137E00123
IO0: 1139E00017
IO1: 1139E00025
SW2 Chassis: 1137E00119
IO0: 1139E00010
IO1: 1139E00020
----------------------------------------------------------
Hello Robert,
Please attempt to issue the following commands in CLI
admin start
config edit
set config blade <ioX>
See if this will allow you to force set the blade to 8Gb. Please provide an update with the results.
Thank You
----------------------------------------------------------
Hi Tameka,
1)
Two QL9200 with two 8Gb 16 port blades each. The ports are only able to go up to 4Gb, CLI reports not licensed for 8Gb usage.
Can you give me licenses to enable the 8Gb please, we are on a limited time window, can we have them tonight?
Two support dump files are attached.
----------------------------------------------------------
SANbox #> show blade io0
Configured Blade Type FC8G16
Current Blade Type FC8G16 (not licensed for 8G)
Port Range 0-15
Configured Admin State Online
Current Admin State Online
Oper State Online
Presence Indicator FullySeated
Beacon Off
Logging On
Serial Number 1139E00017
Planar Part Number 32241-00 A
Boot Version V1.12.5.81.0
Boot Version Code 010c0551
Boot Timestamp Fri Sep 12 14:10:47 2008
POST Fault Code 00000000
POST Status Passed
Test Fault Code 00000000
Test Status NeverRun
Temp Status Normal
Voltage Status Good
Reset Reason HardReset
Fault Status None
Current Faults NoneSANbox #>
SANbox #> admin start
SANbox (admin) #> feature add 40000000-LCAXBK/UXEFAY-1139E00017Blade license upgrade for 8G capability
This feature upgrade does NOT require a switch reset.
Do you want to continue with license upgrade procedure? (y/n): [n] y
Log Msg: [Sun Nov 06 09:36:13.348 UTC 2011][C][8400.0047][Switch][New licenses are being installed]
SANbox (admin) #>SANbox (admin) #> show blade io0Configured Blade Type FC8G16
Current Blade Type FC8G16 (licensed for 8G)
Port Range 0-15
Configured Admin State Online
Current Admin State Online
Oper State Online
Presence Indicator FullySeated
Beacon Off
Logging On
Serial Number 1139E00017
Planar Part Number 32241-00 A
Boot Version V1.12.5.81.0
Boot Version Code 010c0551
Boot Timestamp Fri Sep 12 14:10:47 2008
POST Fault Code 00000000
POST Status Passed
Test Fault Code 00000000
Test Status NeverRun
Temp Status Normal
Voltage Status Good
Reset Reason HardReset
Fault Status None
Current Faults NoneSANbox (admin) #>
0 Comments